Sheaves for sale
I have 2 sheaves for sale which ever one I sell I'm keeping the other. They are for a 700, couple hundred miles on either sheave. I have a hunterworks with 18g weights. The other is a jbs with 16g...
View ArticleClik here to view.
new to the rhino game pics of my o7 660 stroker motor
Hey guys this site is great has already helped my with that pesky reverse rev limator I got a couple of pics here. Its got the adjustible 4_7 gorilla lift 30" silverbacks 660 stroker motor 30lb...
View ArticleRear Axle Orientation
guys I know this may seem like a very easy question, but after searching for an hour I still don't have a concrete answer. With regards to the rear axles on a Rhino 660 I want to know if which rear...
View ArticleMore Low End?
Is it possible to get even more low end out the Rhino? I mainly use mine for work and rarely ever hit more than about 25mph.
View ArticleClik here to view.
Rear Axle Orientation
guys I know this may seem like a very easy question, but after searching for an hour I still don't have a concrete answer. With regards to the rear axles on a Rhino 660 I want to know if which rear...
View ArticleClik here to view.
Sheep crossing photos
Here are a few photos of my trip to sheep crossing or sheep bridge... Two ways to get there, one way coming from bloody basin road off the i17 which is a much longer way and the other shorter way is...
View ArticleClik here to view.
new products by Rugged Radios
RH-5R Rugged Radios 5-Watt Dual Band (VHF/UHF) Handheld Radio [RH-5R] - $85.00 : Rugged Radios: Headsets, Intercoms, 2-Way Racing Radios and Communication for Motorcycles, Offroad, Circle Track, Drag...
View Article2005 Rhino 660 Complete Roller
Stock Everything included minus an engine $2000 (even has a good battery:banana:) Ca Pinkslip in Hand with Current Green Sticker i can remove some items to bring the cost down but will not sell it for...
View ArticleOD clutch weights?
so at 50mph my motor sounds about like its gonna blow. soon imma be runnin 26 or 27" Zillas. i have stock clutch weights. can i put ODs in my standard UTV Crap machined clutch? i can run 59 with a bad...
View ArticleClik here to view.
easy way to get rear axle nuts off!
A old jack I had laying around bolted perfectly to the hub while I put a breaker bar on the other side Attached Thumbnails
View ArticleNeed jetting help ASAP!
The bike has a Dynatek, (basically Muzzy's), and snorkel. It has a 175 jet in now, but the plug looks to be rich. Starts perfect, idles perfect, and cruising around it's fine. When you go WOT it falls...
View ArticleExtended Roll Cage and Seat
Extended roll cage that mounts to existing roll cage and the frame. The cage has a bumper made into it too. The seat fits perfectly in the bed and can be bolted to the bed in 4 places. The seat comes...
View ArticleClik here to view.
660 engine bolt question
Anyone know if a bolt goes in this hole on the back of the cylinder? Attached Thumbnails
View ArticleOEM seat belt for 2011
Anyone have a oem seat belt from a 2011 Rhino they will part with? Mine is missing the red clip that is on the part that you grab with your hand when buckling up. Thanks
View Articlebest cvt belt?
I was wondering what would be the best drive belt for my rhino. 06 660 (686), dry clutch, stage 2 cam, trail and dune riding. Thanks.
View Articlestock bore stroker
so i had a great thought. can a stock bore be made into a stroker and make good power? if i made a 720 stroker, how reliable are they? what kinda power is made over stock with basic mods?
View ArticleClik here to view.
2006 rhino 686
686 12.5 to 1 compression race ported head w/mild cam EPI clutch kit CDI box Dassa racing dual pipes 2.0 King racing shocks offset wheels omf beadlocks 5 seater w/4 pont harnesses stereo lite bar need...
View ArticleI need a slide hammer tool
was wondering if anyone knew where i could get a cv slide hammer tool
View Article